Racing Products

COIL-OVER SPRING COMPRESSOR

IF YOU DON'T NEED THIS, THEN YOUR SPRINGS AREN'T SOFT ENOUGH!
INSTALLS LONG SPRINGS ON COIL-OVERS FOR BIG BAR/SOFT SPRING SET-UPS

Works with all spring diameter sizes from 2 1/2" up to 5"

Installs and removes most coil-over spring/shock combinations

Can be used to install springs without moving the coil-over adjusting nut

Dual stage hydraulic pump for increased travel in removing and installing very long springs from short shocks

Three bar design allows for triangular attachment to the spring to reduce deforming the spring on compression

Upper shock mount centers spring in proper location and allows for user to be able to work on the spring/shock without having to hold the coil-over by hand

Open design allows for installation and removal of coil-over from the front

Portable design allows you to bring it to the track for on-site adjustments

Works on all brands of shocks and springs

Run mouse over to enlarge image

This unit allows for one person to be able to change long springs on coil-overs, safely and efficiently, at the shop or the track!

Price: $649.99
(call or email us today to place your order)

SPRING EXCHANGER

LEAVE YOUR SCALES AT HOME! THIS UNIT WILL ALLOW YOU TO CHANGE YOUR SPRINGS WITHOUT CHANGING THE WEDGE!

RATES AND EXCHANGES SPRINGS/RUBBERS ON ALL TYPES OF COIL-OVER COMBINATIONS

DESIGNED TO WORK IN THE HORIZONTAL POSITION FOR BETTER STABILITY AND EASE IN ADJUSTING THE COIL-OVER NUT
Run mouse over to enlarge image

Change spring rates and spring lengths on coil-over without changing the wedge or ride height and without the need to weigh the car

Change shock brands or coil-over hardware with no confusing measurement conversions

Set up springs in the shop in 1/3 the time on the bench for ease and accuracy

Quickly check spring rate per inch with spring installed on coil-over

Quickly check spring and one or more spring rubbers on coil-over for rate increase per inch

Rate springs all the way to coil bind on coil-over for rate increase per inch

Check combination rate of spring and bump rubber in cars down position for big bar/soft spring set ups (This allows you a way to determine your final combination spring and bump rubber rate in the last inch of travel)

Change spring/bump rubber rates and use the Coil-over Spring Exchanger to insure your nose and cross member height are the same as before (Eliminates track time needed to adjust nose height after spring/rubber rate change!)

All above operations done "on the bench!"

This is an adjustable length unit that allows for most coil-over sizes and brands. Jack has over 10 inches of hydraulic stroke to compress coil-over to final inch of stroke for measuring bump rubber rates and coil bind rates. Measuring is done with a hydraulic load cell and liquid filled 0-2000 psi gauge.

Price: $649.99
(call or email us today to place your order)

ADJUSTABLE DROP DOWN PANHARD BAR BRACKET

LOW IS THE ONLY WAY TO GO!

Allows for quick easy adjustment of the panhard bar on the frame mount
Allows you to set the panhard bar at the bottom of the frame rail
Rotates on 1 3/4" tubing to allow for angled panhard bar mounting
Machined markings make it easy to check location of panhard bar height
Supplied with aluminum adjusting shaft

Price: $299.99
(call or email us today to place your order)

Run mouse over to enlarge image

MANUAL DROP DOWN PANHARD BAR BRACKET

Allows for manual adjustment of the panhard bar on the frame mount

Allows you to set the panhard bar at the bottom of the frame rail

Rotates on 1 3/4" tubing to allow for angled panhard bar mounting

Price: $99.99
(call or email us today to place your order)

Run mouse over to enlarge image

CROSS MEMBER HEIGHT GAUGE

Weld steel block to each side of the cross member
Nylon rods wear off when cross member is at its lowest point
Helps determine your true cross member height
Helps determine the roll in your front end
Easily adjusts up and down with allen head screw
Use these measurements to accurately determine front end geometry and roll center locations, by inputing them into your software

Each Package comes with (2) weld on steel blocks and (4) nylon measuring sticks

Price: $19.95
(call or email us today to place your order)

Run mouse over to enlarge image

Replacement nylon measuring sticks package
(package includes 10 nylon measuring sticks)

Price: $17.50
(call or email us today to place your order)